This project “The Production of Ceiling Board from Local Raw Materials” was carried out basically using raw materials which was sourced locally. These raw materials are found to be very much in abundance. Some are materials sourced from the ground and others are from agricultural wastes.
Three different types of ceiling boards were produced, their difference being in the type of fibre that was used. The fibres used for this different type includes; cellulose fibre obtained from pulped carton, saw dust and rice husk.
The raw materials used for the production of the different ceiling boards includes, cement, calcium carbonate (CaCo3), Kaolin, starch and water.
The first type produced is from pulped carton. First, the cartons were collected, size reduce, soaked in a large quantity of water for 24hours, strained to remove the water and the milled by grinding using a motar and pestle. The quantity to be used was weighed out. The other raw materials which include starch, powdered kaolin, calcium carbonate and water were all measured. The pulped carton was poured and thoroughly mixed. The CaCo3, kaolin and starch and water were all measured. The pulped Carton was poured into the reactor; next cement was poured and thoroughly mixed. The CaCo3, kaolin and starch was added one after the other while stirring continued. Finally, water was added sparingly and gradually until a very smooth slurry was obtained. This was then poured into a mould and smoothened out using a roller and was left to dry. It took 7days for it to get dry.
The next produced was ceiling board from sawdust. The sawdust was first sieved, soaked for a day and then strained to remove the water. The quantity used was measured as well as all the other raw materials that was used. The same procedure was repeated as that of the first method and it was allowed to dry. It took three days to dry.
Finally, ceiling board using rice husk was produced. The rice husk was sieved, materials to be used weighed out and procedure repeated again in this case and allowed to dry. It took 5 days for it to dry. Drying was done with solar energy for all cases.
The three different types were subjected to different test. This includes; moisture content test percentage humidity, bursting strength. The weight of the wet samples and dry samples was obtained as well as the density and volume.
Finally, the different ceiling boards were coasted. Ceiling board from cellulose fibre (Sample A) costs N186.00 for the production, that of sawdust costs N184.00 while that of rice husk costs N185.00.
Title page
Letter of transmittal
Approval page
Dedication
Acknowledgement
Abstract
Table of content
CHAPTER ONE
1.0 INTRODUCTION
1.1 Aims and Objectives of the Project
CHAPTER TWO
LITERATURE REVIEW
2.0 History of Ceiling Board
2.1 Types of Ceiling Board
2.1.1 Asbestos Cement Ceiling Board
2.1.2 Acoustical Ceiling Board
2.1.3 Gypsum Ceiling Board
2.1.4 Gypsum Fibre Celling Board
2.1.5 Cement Fibre Ceiling Board
2.2 Raw Materials Used For The Production Of Ceiling Boards
2.2.1 Cement
2.2.2 Fibre
2.2.3 Starch
2.2.4 Calcium Carbonate
2.2.5 Kaolin
2.2.6 Additives
2.2.7 Pigments
2.2.8 Fludifiers
2.3 The Study Of Thermal Properties Of The Ceiling Boards
2.3.1 Thermal Comfort
2.3.2 The Principles Of Thermal Insulation
2.3.3 Typical Thermal Properties Of Some Ceiling Boards
2.3.4 Conductivity Of Porous Materials
2.3.5 Surfaces Coefficients
2.4 Study Of Acoustic Properties
2.4.1 Acoustic Properties
2.4.2 Sound Absorption
2.4.3 Basic Factors In Acoustic Design
2.4.4 Manufacturing Process
2.5 Manufacturing Process
2.5.1 The manufacture of wood wool cements ceiling board.
2.5.2 Production Of Ceiling From Various Types Of Fibred
2.5.3 Production Of Ceiling Board From Paper
CHAPTER THREE.
3.0 Manufacturing Process
3.1 Apparatus and Equipment Used For the Production
3.2 Chemicals And Materials Used For The Production
3.3 Composition Of Materials Used For The Production
3.4 Preparation Of Raw Materials
3.5 Production Procedure
3.6 Dying
3.7 Trimming
3.8 Analysis Of The Samples
3.8.1 Introduction of the samples
3.8.2 Composition of sample sheet
3.8.3 Test and result of test
3.8.4 Rate of drying
3.8.5 Bursting strength
3.8.6 Moisture strength
CHAPTER FOUR
4.0 Costing
4.1 Cost of Raw Materials
CHAPTER FIVE
5.0 DISCUSSION
CHAPTER SIX
6.0 CONCLUSION/RECOMMENDATION
Manufacture Of Ceiling Board Using Local Materials. (n.d.). UniTopics. https://www.unitopics.com/project/material/manufacture-of-ceiling-board-using-local-materials/
“Manufacture Of Ceiling Board Using Local Materials.” UniTopics, https://www.unitopics.com/project/material/manufacture-of-ceiling-board-using-local-materials/. Accessed 22 November 2024.
“Manufacture Of Ceiling Board Using Local Materials.” UniTopics, Accessed November 22, 2024. https://www.unitopics.com/project/material/manufacture-of-ceiling-board-using-local-materials/
Here’s a typical structure for Manufacture Of Ceiling Board Using Local Materials research projects:
- The title page of Manufacture Of Ceiling Board Using Local Materials should include the project title, your name, institution, and date.
- The abstract of Manufacture Of Ceiling Board Using Local Materials should be a summary of around 150-250 words and should highlight the main objectives, methods, results, and conclusions.
- The introduction of Manufacture Of Ceiling Board Using Local Materials should provide the background information, outline the research problem, and state the objectives and significance of the study.
- Review existing research related to Manufacture Of Ceiling Board Using Local Materials, identifying gaps the study aims to fill.
- The methodology section of Manufacture Of Ceiling Board Using Local Materials should describe the research design, data collection methods, and analytical techniques used.
- Present the findings of the Manufacture Of Ceiling Board Using Local Materials research study using tables, charts, and graphs to illustrate key points.
- Interpret Manufacture Of Ceiling Board Using Local Materials results, discussing their implications, limitations, and potential areas for future research.
- Summarize the main findings of the Manufacture Of Ceiling Board Using Local Materials study and restate its significance.
- List all the sources you cited in Manufacture Of Ceiling Board Using Local Materials project, following a specific citation style (e.g., APA, MLA, Chicago).