This research was carried out with the sole aim of monitoring interface in the transportation of petroleum pipeline products and the analysis of this product from Enugu depot. In the research it was observed that product contaminates each other if interface was not properly monitored and cut at the appropriate time.
The three major products that were considered in this research were premium motor spirit (PMS) automotive gas premium (AGO0 and dual purpose kerosene (DPK).
The tests carried out point test smoke point test, initial and final boiling point test (Distillation), temperature and density test, to ascertain the standard quality specification and the extent of their purity.
It was observed from the result that the flash point value for DPK and AGO were 430c and 820c respectively. The average smoke point test values for DPK product was 21.92mm. the initial and final boiling point of PMS were350c and 1750c, respectively. The observed density at the DPK/AGO interface monitoring test were 819 kg/m3 and 850 kg/m3 and corrected densities for DPK and AGO were 830.2kg/m3 and 859.9kg/m3 respectively. The interface reception cut point for DPK/AGO interface monitoring was made at the corrected density of 849.0 kg/m3. And the temperature of DPK and AGO were 310c respectively.
The result from the analysis revealed that the boiling point of PMS was far more lower than that of AGI and DPK, which implies that PMS has a higher volatility than the two other products the flash point test revealed that the minimum temperature at which AGO and DPK ignites was 66.50c and 430c PMS was not determined because of its high volatility. Also, the standard minimum smoke point of DPK was determined to be 22mm. The smoke point test for AGO and PMS were not carried out because, they were not domestically used and their combustion normally takes value in an engine.
This research has become very necessary because it reveals the proper way pf handling petroleum pipeline product to meet standard specification for domestic and industrial use.
Title page
Approval page
Letter of transmittal
Dedication
Acknowledgement
Abstract
Table of contents
CHAPTER ONE
1.0 Introduction
1.1 Historical perspective
1.2 Introduction to petroleum transportation by pipeline
1.3 Product movements and handling
1.4 Batching procedure
1.5 Interface detection and control
1.6 Interface growth
1.7 Product quality control
1.8 Sample
1.9 Product contamination
CHAPTER TWO
2.0 Literature review
2.1 Historical review of interface
2.2 Pipeline hydraulics
2.3 Laminal and turbulent flow
2.4 The Reynolds number
2.5 Operating philosophy
CHAPTER THREE
3.0 Experimental method/ procedure
3.1 List of laboratory equipment
3.2 Experiment method
3.3 Interface monitoring test (first step)
3.4 Experimental test on the various pipeline product (second step)
3.4.1 Flash point test
3.4.2 Smoke point test
3.4.3 Distillation test
3.4.4 Temperature and relative density test
CHAPTER FOUR
4.0 Experimental results
CHAPTER FIVE
5.0 Discussion
CHAPTER SIX
6.0 Conclusion
CHAPTER SEVEN
7.0 Recommendation
References
Appendices
Interface Monitoring And Analysis Of Pipeline And Products Marketing Company Limited. (n.d.). UniTopics. https://www.unitopics.com/project/material/interface-monitoring-and-analysis-of-pipeline-and-products-marketing-company-limited/
“Interface Monitoring And Analysis Of Pipeline And Products Marketing Company Limited.” UniTopics, https://www.unitopics.com/project/material/interface-monitoring-and-analysis-of-pipeline-and-products-marketing-company-limited/. Accessed 25 November 2024.
“Interface Monitoring And Analysis Of Pipeline And Products Marketing Company Limited.” UniTopics, Accessed November 25, 2024. https://www.unitopics.com/project/material/interface-monitoring-and-analysis-of-pipeline-and-products-marketing-company-limited/
Here’s a typical structure for Interface Monitoring And Analysis Of Pipeline And Products Marketing Company Limited research projects:
- The title page of Interface Monitoring And Analysis Of Pipeline And Products Marketing Company Limited should include the project title, your name, institution, and date.
- The abstract of Interface Monitoring And Analysis Of Pipeline And Products Marketing Company Limited should be a summary of around 150-250 words and should highlight the main objectives, methods, results, and conclusions.
- The introduction of Interface Monitoring And Analysis Of Pipeline And Products Marketing Company Limited should provide the background information, outline the research problem, and state the objectives and significance of the study.
- Review existing research related to Interface Monitoring And Analysis Of Pipeline And Products Marketing Company Limited, identifying gaps the study aims to fill.
- The methodology section of Interface Monitoring And Analysis Of Pipeline And Products Marketing Company Limited should describe the research design, data collection methods, and analytical techniques used.
- Present the findings of the Interface Monitoring And Analysis Of Pipeline And Products Marketing Company Limited research study using tables, charts, and graphs to illustrate key points.
- Interpret Interface Monitoring And Analysis Of Pipeline And Products Marketing Company Limited results, discussing their implications, limitations, and potential areas for future research.
- Summarize the main findings of the Interface Monitoring And Analysis Of Pipeline And Products Marketing Company Limited study and restate its significance.
- List all the sources you cited in Interface Monitoring And Analysis Of Pipeline And Products Marketing Company Limited project, following a specific citation style (e.g., APA, MLA, Chicago).