Fabrication Of Twin Leaf Metal Door

ABSTRACT

          This project report is based on fabrication of twin leaf metal door. A mental door is a movable structure used to close off an entrance typically consisting of  a panel that swings on lings, side or rotate.

This metal door more reliable and strong and has much good looking appearance than other doors like, wooden  door, glass door, leather door e.t.c various fabrication processes such as: marking out, cutting, bending, joining or welding, grinding, spraying e.t.c were adopted and implemented in the fabrication of this twin leaf metal door. Peep hole was fixed on the door to screw visitor and admit on choice, the main purpose is to ensure safety and protection.

The material used to make this protect to be well strong design are as follows-galvanised metal plate, square pipe lock set key paint, hinges, guage 12 electrode and grinding disk and the major reason of using the material is to provide good making features of the door which will meet up with nowadays demand and designs, and in order to expose students to how to use different types of simple tools and some machines. The special features on the door are as follows: pin hole glass, lock set key, hinges small, square pipe design, glass paint use to coat  the door for rusting. 

TABLE OF CONTENT

Title page

Certification

Dedication

Acknowledgement

Abstract

Table of content

List of figure

Nomenclature

CHAPTER ONE

Introduction

1.1     Background of the study

1.2     Literature review

1.3     Aim

1.4     Objectives of the project

CHAPTER TWO

ANALYSIS OF ALTERNATIVE METHOD AND CHOICE OF BEST ALTERNATIVE.

2.1     Definition of door

2.2     Types of door

2.3.1  Advantage of metal door opening

2.3.2  Advantage of metal door closure

2.4     Definition of welding

2.5     Types of welding

5.4     Welding operation

5.5     Types of welding operation

5.6     Safety operation

5.7.1  Welding equipment

5.7.2  Electrode Holder

5.8     Precautionary measures against other Risks

5.9     Finishing Touches

5.10   Maintenance

5.11   Problem Encountered

5.12   Bills of Engineering measurement and Evaluation

CHAPTER SIX

CONCLUSION AND RECOMMENDATION

6.1     Conclusion

6.2     Recommendation

References

CHAPTER ONE

1.1     BACKGROUND OF THE STUDY

          Many years ago, different types of door were in use which includes doors were either by wood or grass. These doors were made then to meet the purpose of security both life and property. It was later discovered that doors made with wood do not last long.

They have a short life span. More so, they are not durable they go demanded very easily and quickly and they cannot with stand high degree of strain.

Doors made with wood are very risky to be put at open place, this is because doors made with wood when faced with water frequently. It get demand. In addition, termites could make the life span of wooden short.

Also, considering the rate of which armed robber break into house in our society, one would agree. That wooden door gave then the to do so because, it could easily be damaged.

Meanwhile, based on the informational realms and also the urged to improve technologically, so as technologist in training, we have of come up with a design to serve as an alternative mean of making doors of different patterns of today. The pattern that seem to give doors a long of man and properties.

1.2 LITERATURE REVIEW

Many years ago, doors were made with either wood or grasses the general purpose of serves as a mean of secreting both lives and properties and also serve as a feature of any building.

When open, they admit ventilation and light. Doors used to control the physical atmosphere within a space by enclosing the air draft, so that interiors may be more effectively heated or cooled. Door are significant in preventing the spread of fire they are also as barrier for esthetic, keeping formal and utility area separates. Door are usually different in most places, due to chance of temperature and humidity, doors usually have to be framed. The Greeks and Romans used many styles of doors single, double sliding of folding the doors as well as many other found throughout Europe’s past were made of brome. This seemed to be going material used and purpose of doors.

1.3 AIMS AND OBJECTIVES

1. To over come the problem of short life span of doors
2. To reduce the risk of human life and properties cause by wooden and grass door during burglary.
3. To change the local method of door design to the modern method e.g wooden door to metal door
4. To allow student to be more expose to use of some complex machine in the workshop and basic workshop procedure
5. To beautify the building
6. To produce decent, stronger and well designed types of door by using metal.

7       To practical’s the theoretical work done in the lecture room.