Fabrication Of The A Metallic Bookshelf

ABSTRACT

Knowledge could only be obtained successively by the use of books for research. This can be achieved only by preserving books already purchased. As a result we fabricate a metallic shelf made up of metallic sheet. Precisely mild steel sheets. The mild steel used for the fabrication of the shelf is 1.5mm (16gauge) mild steel.
The shelf is made up of 3 partition. In fabricating the metallic shelf several process where involved. We plundered on the material to be used that can hold the number of the books i.e. the strength of the material.
Thereafter accurate measurements of the mild sheets were made we also considered the rigidity of the metallic shelf. This led us to using square pipes for the support of the shelf. The square pipes were also measured to give the dimensions use.
The already cut square pipes were used form the frame by welding it together. Then the already measured and cut mild sheets were also welded to the frame. The doors are made up of the square pipes and wire gauze welded together. The shelf was also painted to give good outlook after smoothening and filling. Rollers were also fixed beneath to enhance good and easy movement of the shelf due to its weight.

TABLE OF CONTENTS

Title Page ii
Letter of Transmittal iii
Release Page iv
Signature Page v
Approval Page vi
Dedication vii
Acknowledgement viii
Table of content ix
Abstract xi

CHAPTER ONE
1.1 Introduction 1
1.2 Description of the bookshelf 2

CHAPTER TWO
2.1 Mode of Operation 6
2.2 Material selection 8

CHAPTER THREE
3.1 Fabrication 10
3.2 Fabrication Analysis 10
3.3 Capacity of The Bookshelf 12
3.4 Fabrication Experiment 12
3.5 Construction 14

CHAPTER FOUR
4.1 Cost of Analysis 17

CHAPTER FIVE
5.1 Conclusion 20
5.2 Recommendation 21
Reference 22

APA

Fabrication Of The A Metallic Bookshelf. (n.d.). UniTopics. https://www.unitopics.com/project/material/fabrication-of-the-a-metallic-bookshelf/

MLA

“Fabrication Of The A Metallic Bookshelf.” UniTopics, https://www.unitopics.com/project/material/fabrication-of-the-a-metallic-bookshelf/. Accessed 22 November 2024.

Chicago

“Fabrication Of The A Metallic Bookshelf.” UniTopics, Accessed November 22, 2024. https://www.unitopics.com/project/material/fabrication-of-the-a-metallic-bookshelf/

WORK DETAILS

Chapters:
5
Pages:
31
Words:
3669

Here’s a typical structure for Fabrication Of The A Metallic Bookshelf research projects:

  • The title page of Fabrication Of The A Metallic Bookshelf should include the project title, your name, institution, and date.
  • The abstract of Fabrication Of The A Metallic Bookshelf should be a summary of around 150-250 words and should highlight the main objectives, methods, results, and conclusions.
  • The introduction of Fabrication Of The A Metallic Bookshelf should provide the background information, outline the research problem, and state the objectives and significance of the study.
  • Review existing research related to Fabrication Of The A Metallic Bookshelf, identifying gaps the study aims to fill.
  • The methodology section of Fabrication Of The A Metallic Bookshelf should describe the research design, data collection methods, and analytical techniques used.
  • Present the findings of the Fabrication Of The A Metallic Bookshelf research study using tables, charts, and graphs to illustrate key points.
  • Interpret Fabrication Of The A Metallic Bookshelf results, discussing their implications, limitations, and potential areas for future research.
  • Summarize the main findings of the Fabrication Of The A Metallic Bookshelf study and restate its significance.
  • List all the sources you cited in Fabrication Of The A Metallic Bookshelf project, following a specific citation style (e.g., APA, MLA, Chicago).
WORK DETAILS

Chapters:
5
Pages:
31
Words:
3669