Design Ans Construction Of An Audio Mixer With Multiple Controls

When recording sound from several orchestral instruments being played by different musicians using a single microphone, the only way to adjust the sound balance is to change the position of the musicians relative to the microphone. When recording direct to stereo master tape, it’s crucial to make sure that all the voices and instruments sound right before you hit the record button. Presented here is an eight-input audio mixer circuit with bass, treble, volume and balance controls, which you can use to balance sounds from all the sources until you have the desired mix. For capturing the sound from various sources, the audio mixer employs up to eight microphones.

3.1                                                       BLOCK DIAGRAM

Before carrying out any project, the block diagram must be drawn and fully understood. Block diagram gives a pictorial understanding of any work. The block diagram of the system is as below:

TABLE OF CONTENTS

TITLE PAGE

APPROVAL PAGE

DEDICATION

ACKNOWELDGEMENT

ABSTRCT

TABLE OF CONTENT

CHAPTER ONE

• INTRODUCTION

1.1     AIM/OBJECTIVE OF THE PROJECT

1.2     SIGNIFICANCE OF THE PROJECT

1.3     APPLICATION OF THE PROJECT

1.4      PURPOSE OF THE PROJECT

1.5      SCOPE OF THE PROJECT

1.6      PROBLEM OF THE PROJECT

1.7      LIMITATION OF THE PROJECT

1.8     PROJECT ORGANISATION

CHAPTER TWO

2.0 LITERATURE REVIEW

2.1      HISTORICAL BACKGROUND OF AN AUDIO MIXER

2.2      REVIEW OF AUDIO MIXING

2.3      REVIEW OF MIXERS

2.4      REVIEW OF TYPES OF MIXERS

2.5      FEATURES OF MIXERS

CHAPTER THREE

CONSTRUCTION METHODOLOGY

3.1 BLOCK DIAGRAM OF THE SYSTEM

3.2 CIRCUIT DIAGRAM

3.3 CIRCUIT DESCRIPTION

3.4 SYSTEM OPERATION

3.5 COMPONENTS LIST

3.6 12V REGULATED POWER SUPPLY

3.7 DESCRIPTION OF MAJOR COMPONENTS USED

CHAPTER FOUR

 

4.0 RESULT ANALYSIS

4.1 CONSTRUCTION PROCEDURE AND TESTING

4.2 ASSEMBLING OF SECTIONS

4.3 CONSRUCTION OF THE CASING

4.4 ECONOMIC OF THE PROJECT

4.5 PROJECT VIABILITY

4.6 PROJECT RELIABILITY

4.7 PROJECT MAINTAINABILITY

4.8 PROJECT EVALUATION

4.9 TESTING, TROUBLESHOOTING AND REMEDY

CHAPTER FIVE

CONCLUSIONS

RECOMMENDATION

REFERENCES

Audio mixer circuit

Fig. 1 shows the block diagram of the audio mixing system along with the audio power amplifier, while the circuit of the audio mixer along with a tone controller is shown in Fig. 2. The power supply and audio power amplifier circuits are shown in Figs 3 and 4, respectively.

Fig. 1: Block diagram of the audio mixer with bass, treble, volume and balance controls

Here, dual operational amplifier IC 747 (IC3) is used for mixing several inputs without any mutual interaction. The two internal amplifiers share a common bias network and power supply. The IC has short-circuit protection and wide common-mode and differential voltage ranges.

In this application, +12V and –12V regulated DC supplies are used for operation of IC 747. The microphone output signals M1 through M4, after their individual level adjustments, are mixed and applied across the differential input terminals (pins 1 and 2). Similarly, microphone outputs M5 through M8 are applied across the differential input terminals (pins 7 and 6) of the second amplifier inside op-amp IC 747 after their individual level adjustments.

Circuit Operation

For level adjustment, logarithmic variable resistors VR1 through VR4 and VR5 through VR8, respectively, are employed while feeding the output from respective microphones to the input of the two amplifiers inside IC 747. The outputs of the two amplifiers taken from pins 12 and 10, respectively, are combined at the junction of resistors R9 and R10 before feeding to the next stage (tone controller) via capacitor C12 (10 µF). The overall gain of individual amplifiers can be adjusted with the help of potmeters VR9 and VR10, respectively.

The amplified mixed signal output of IC 747 is applied to shorted input pins 15 and 4 of stereo tone controller IC TDA1524A (IC4). TDA1524A is designed as an active stereo-tone/volume control for car radios, TV receivers and mains-fed equipment. It includes functions for bass and treble control, volume control with built-in contour (can be switched off) and balance. All these functions can be controlled by DC voltages or by single linear potentiometers. This IC serves as an efficient tone controller. Although it may work reasonably well with 9V DC supply, for better bass response, a 12V supply can be used. A good heat-sink is necessary for longer life and better performance of the IC.

Fig. 2: Circuit of audio mixer with bass, treble, volume and balance control

Features of TDA1524A are:

1. Simple construction
2. Low noise and distortion
3. Switchable contour (for quick changing of the tonal response)
4. Its output can drive most power amplifiers.
5. Bass emphasis can be increased by incorporating a double-pole, low-pass filter
6. Wide power supply voltage range

General specifications are:

1. DC input: 12V (typical)
2. DC battery: 35 mA
3. Maximum output: 3V RMS
4. Maximum input: 2.5V
5. Maximum gain: 21.5 dB
6. Volume control range: –80 to+121.5 dB
7. THD at 1 kHz: 0.3%
8. Ripple rejection at 100 Hz: 50 dB

Potmeters VR11, VR12, VR13 and VR14 are meant for adjustment of volume, balance, bass and treble, respectively. Switch S2 is contour switch, which can be used to change the tonal response of the of the IC. The outputs are available at pins 8 and 11 for right and left channel, respectively. (EFY note. Since both the left- and right-channel input pins 15 and 4 have been shorted in this application, the IC acts as a mono volume/tone control circuit.)

Audio Power Amplifier

The audio amplifier circuit shown in Fig. 4 is optional. One can use much higher-power audio amplifier along with the audio mixer circuit.

The low-power audio amplifier employing IC LM386 (IC5) shown in Fig. 4 can output a maximum audio power of 1 watt. It gets +12V DC supply at its pin 6. The audio input from sources like Walkman and audio mixer can be fed to pin 3 of IC5 through volume control VR15.

Fig. 3: Power supply circuit

The gain of LM386 is internally set to 20 to keep the external part count low. However, to make LM386 a more versatile amplifier, pins 1 and 8 are provided for setting the gain—externally to any value between 20 and 200—by using an appropriate combination of a resistor and a capacitor. If only a capacitor is put between pins 1 and 8 using switch S3 as shown in Fig. 4, the gain would increase to 200 (46 dB). The amplified output is taken from pin 5 and fed to the loudspeaker through electrolytic capacitor C39 (100 µF). The higher the value of C39, the higher the pitch of the audio frequency response in the speaker.

Fig. 4: Low-power audio amplifier circuit

Power supply

The power supply section for the circuit is shown in Fig. 3. It consists of a step-down transformer (230V AC primary to 12V-0-12V, 1A secondary), bridge rectifier, filter network and regulator ICs 7812 and 7912 to provide +12V and –12V regulated DC outputs, respectively. When switch S1 is closed, the presence of power is indicated by the glowing of LED1.

Construction

Assemble the circuit on any general-purpose PCB. Mount IC bases on the PCB. There is no soldering method that is ideal for all IC packages. The use of IC bases prevents damage to the ICs while soldering and also makes it easy to replace them. Use audio input jack connectors for M1 through M8 input points. Also use audio output connectors at the outputs of IC4.

Fig. 5: Combined actual-size, single-side PCB for audio mixer and power supply circuits Fig. 6: Components layout for the PCB in Fig. 5

Download PCB and component layout PDFs: click here

A combined actual-size, single-sided PCB layout for Figs 2 and 3 is shown in Fig. 5 and its components layout in Fig. 6. The solder-side PCB layout for Fig. 4 is shown in Fig. 7 and its components layout in Fig. 8.

Note

If you are not using IC base for TDA1524A, the maximum permissible temperature of the solder is 260°C; solder at this temperature must not be in contact with the joint for more than five seconds. The total contact time of successive solder waves must not exceed five seconds while using wave soldering.

Fig. 7: Solder-side PCB layout for the audio amplifier circuit Fig. 8: Components layout for the PCB in Fig. 7

Testing procedure

1. After assembling the PCB, check the circuit connections before switching on the power supply.
2. Use a standard microphone at the first input point M1 and then keep it near an audio source. You can use the power amplifier circuit given here for testing or another higher-output power amplifier.
3. Vary VR1 slowly until a clear and distortion-free amplified output is obtained.
4. If the sound output is not clear and VR1 does not help, vary gain control VR9.
5. If the problem still persists, check volume, balance, bass and treble controls.
6. Check the various controls in your audio power amplifier section.
7. Repeat steps 2 through 5 for the rest of the inputs. Having checked all the inputs, now the audio mixer is ready for use.

 

 

MIXER CIRCUIT A mixer is a circuit that combines two or more signals together.AUDIO MIXERAn audio mixer is the circuit which combines different audio signals of audio frequency band to give desired music output. :

MIXER CIRCUIT A mixer is a circuit that combines two or more signals together.AUDIO MIXERAn audio mixer is the circuit which combines different audio signals of audio frequency band to give desired music output.

 

INTRODUCTION :

Analog mixers Digital mixers A typical analog mixing board has three sections: Channel inputs Master controls Audio level metering INTRODUCTION

 

Slide 4:

Amplitude leveling Each channel on a mixer has an audio taper(potentiometer) controlled by a sliding volume control that allows adjustment of the level, or amplitude of that channel in the final mix. A group of channels that are then added to get the final mix.

 

OBJECTIVE :

VOLUME BALANCE BASS TREBBLE GAIN CONTROL OBJECTIVE

 

BLOCK DIAGRAM :

BLOCK DIAGRAM

 

MIXER IC IC 747 :

MIXER IC IC 747

 

STERIO TONE CONTROLER :

TDA1524A IC STERIO TONE CONTROLER

 

AMPLIFIER LM386 :

AMPLIFIER LM386

 

CIRCUIT DIAGRAM :

CIRCUIT DIAGRAM AMPLIFIER

 

EQUALISER :

Bass: the band lower frequencies. Treble: the band of high frequencies. Balance: equilibrium between the stereo output channels. EQUALISER

 

Slide 13:

Virtual mixing Increasingly, the mixing process can be performed on screen, using computer software and associated input, output and recording hardware. The traditional large control surface of the mixing console is not utilized, saving space at the engineer’s mix position. Some virtual mixing uses digital controls of analog audio circuitry, but most virtual mixers are fully digital so as to save cost and physical space. In the virtual studio, there is either no normal mixer fader bank at all or there is a compact group of motorized faders designed to fit into a small space and connected to the computer via USB or Firewire. Many project studios use such a space-efficient solution, as the mixing room at other times can serve as business office, media archival, etc. Virtual mixing is heavily integrated as part of a digital audio workstation.

 

APPLICATIONS :

Public address systems: using multiple Microphones Mixing console: Device to combine musical instruments and vocals to the correct level. Radio broadcasts: No-input mixer: Film post-production: DJ musical equipment: APPLICATIONS