ABSTRACT
The hot water pipe from the water geyser of your bathroom may burst if it gets overheated and is left unattended. This overheating indicator circuit monitors the temperature of the water pipe. If the temperature of the pipe goes above a certain limit, it flashes an LED. The circuit uses a small sensor with an inbuilt thermostat. It is actually an automatically resettable thermal switch that operates whenever its temperature exceeds the set limit. It is available in two versions, viz, normally open (N/O) and normally closed (N/C).
TABLE OF CONTENTS
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWLEDGEMENT
ABSTRACT
TABLE OF CONTENT
CHAPTER ONE
1.0 INTRODUCTION
1.1 BACKGROUND OF THE PROJECT
1.2 AIM OF THE PROJECT
1.3 OBJECTIVE OF THE PROJECT
1.4 SIGNIFICANCE OF THE PROJECT
1.5 PURPOSE OF THE PROJECT
1.6 APPLICATION OF THE PROJECT
1.7 ADVANTAGES OF THE PROJECT
1.8 PROBLEM/LIMITATION OF THE PROJECT
1.9 PROJECT ORGANISATION
CHAPTER TWO
2.0 LITERATURE REVIEW
2.1 REVIEW OF RELATED STUDIES
2.2 REVIEW OF RELATED TERMS
CHAPTER THREE
3.0 CONSTRUCTION METHODOLOGY
3.1 SYSTEM CIRCUIT DIAGRAM
3.2 SYSTEM OPERATION
3.3 CIRCUIT DESCRIPTION
3.4 SYSTEM CIRCUIT DIAGRAM
3.5 CIRCUIT OPERATION
3.6 IMPORTANCE AND FUNCTION OF THE MAJOR COMPONENTS USED IN THIS CIRCUIT
3.7 POWER SUPPLY UNIT
CHAPTER FOUR
RESULT ANALYSIS
4.0 CONSTRUCTION PROCEDURE AND TESTING
4.1 CASING AND PACKAGING
4.2 ASSEMBLING OF SECTIONS
4.3 TESTING
4.4.1 PRE-IMPLEMENTATION TESTING
4.4.2 POST-IMPLEMENTATION TESTING
4.5 RESULT
4.6 COST ANALYSIS
CHAPTER FIVE
5.0 CONCLUSION
5.1 RECOMMENDATION
5.2 REFERENCES
Design And Construction Of An Over-Heating Indicator For Water Pipe. (n.d.). UniTopics. https://www.unitopics.com/project/material/design-and-construction-of-an-over-heating-indicator-for-water-pipe/
“Design And Construction Of An Over-Heating Indicator For Water Pipe.” UniTopics, https://www.unitopics.com/project/material/design-and-construction-of-an-over-heating-indicator-for-water-pipe/. Accessed 22 November 2024.
“Design And Construction Of An Over-Heating Indicator For Water Pipe.” UniTopics, Accessed November 22, 2024. https://www.unitopics.com/project/material/design-and-construction-of-an-over-heating-indicator-for-water-pipe/
Here’s a typical structure for Design And Construction Of An Over-Heating Indicator For Water Pipe research projects:
- The title page of Design And Construction Of An Over-Heating Indicator For Water Pipe should include the project title, your name, institution, and date.
- The abstract of Design And Construction Of An Over-Heating Indicator For Water Pipe should be a summary of around 150-250 words and should highlight the main objectives, methods, results, and conclusions.
- The introduction of Design And Construction Of An Over-Heating Indicator For Water Pipe should provide the background information, outline the research problem, and state the objectives and significance of the study.
- Review existing research related to Design And Construction Of An Over-Heating Indicator For Water Pipe, identifying gaps the study aims to fill.
- The methodology section of Design And Construction Of An Over-Heating Indicator For Water Pipe should describe the research design, data collection methods, and analytical techniques used.
- Present the findings of the Design And Construction Of An Over-Heating Indicator For Water Pipe research study using tables, charts, and graphs to illustrate key points.
- Interpret Design And Construction Of An Over-Heating Indicator For Water Pipe results, discussing their implications, limitations, and potential areas for future research.
- Summarize the main findings of the Design And Construction Of An Over-Heating Indicator For Water Pipe study and restate its significance.
- List all the sources you cited in Design And Construction Of An Over-Heating Indicator For Water Pipe project, following a specific citation style (e.g., APA, MLA, Chicago).