ABSTRACT
This device is used by those who are frequently on the move. It is used to keep your tea, coffee or food warm while consuming little power. The circuit is simple and uses a ubiquitous timer 555 as a free-running astable multivibrator. Diodes 1N4148 are connected in reverse direction to facilitate maximum variation of the duty cycles. The aim of this work is achieved by connecting up to five 10W heating elements in parallel, totaling 50 watts. The consumption of current will be significantly less if fewer coil elements are connected in parallel through toggle switches S2 through S4. Each of these switches has a 6A rating.
TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
1.0 INTRODUCTION
1.1 BACKGROUND OF THE PROJECT
- PURPOSE OF THE PROJECT
- AIM OF THE PROJECT
- OBJECTIVE OF THE PROJECT
- PURPOSE OF THE PROJECT
- LIMITATION OF THE PROJECT
- ADVANTAGES OF THE PROJECT
- PROBLEM OF THE PROJECT
- APPLICATION OF THE PROJECT
- RESEARCH QUESTION
- PROJECT ORGANISATION
CHAPTER TWO
LITERATURE REVIEW
- OVERVIEW OF THE STUDY
- REVIEW OF THE RELATED STUDY
CHAPTER THREE
3.0 CONSTRUCTION METHODOLOGY
3.1 BASIC OF THE SYSTEM
3.2 BLOCK DIAGRAM OF THE SYSTEM
3.3 SYSTEM OPERATION
3.4 CIRCUIT DIAGRAM
3.5 CIRCUIT DESCRIPTION
3.6 DESCRIPTION OF COMPONENTS USED
3.7 POWER SUPPLY UNIT
CHAPTER FOUR
4.0 TESTING AND RESULTS
- CONSTRUCTION PROCEDURE AND TESTING
- INSTALLATION OF THE COMPLET DESIGN
- ASSEMBLING OF SECTIONS
- TESTING OF SYSTEM OPERATION
- COST ANALYSIS
CHAPTER FIVE
- CONCLUSION
- RECOMMENDATION
- REFERENCES
Keyword: in-car food and beverage warmer, commercial food warmers, portable food warmers, food warmer box, commercial countertop food warmer, food warmer lunch box, food warmer container, food warmers target, table top food warmer.
Car Food And Beverage Warmer Circuit Diagram: Power transistor T1 is Darlington type with 5A capacity and output of more than 60 watts. The chosen discrete components assure fixed frequency of 1 Hz (approximately) at pin 3 of timer IC1 (555). Resister R1 and potmeter VR1 (1-mega-ohm) allow adjustment of the duty cycle. The higher the duty cycle, the higher the output of the heater.
You can connect up to five 10W heating elements in parallel, totaling 50 watts. The consumption of current will be significantly less if fewer coil elements are connected in parallel through toggle switches S2 through S4. Each of these switches has a 6A rating.
Assemble the circuit on a general-purpose PCB. Mount power transistor TIP120 on a thick heat-sink. Isolate the circuit from the heating elements using only two wire connections. Use wires that can carry more than 6A current. Fix the coil elements below an aluminium or steel rectangular plate which is at least 1mm thick. Do not forget to insulate the heating plate from the elements. Use the car battery for the power supply with a proper current-carrying-capacity wire.
Design And Construction Of An In-Car Food And Beverage Warmer. (n.d.). UniTopics. https://www.unitopics.com/project/material/design-and-construction-of-an-in-car-food-and-beverage-warmer/
“Design And Construction Of An In-Car Food And Beverage Warmer.” UniTopics, https://www.unitopics.com/project/material/design-and-construction-of-an-in-car-food-and-beverage-warmer/. Accessed 22 November 2024.
“Design And Construction Of An In-Car Food And Beverage Warmer.” UniTopics, Accessed November 22, 2024. https://www.unitopics.com/project/material/design-and-construction-of-an-in-car-food-and-beverage-warmer/
Here’s a typical structure for Design And Construction Of An In-Car Food And Beverage Warmer research projects:
- The title page of Design And Construction Of An In-Car Food And Beverage Warmer should include the project title, your name, institution, and date.
- The abstract of Design And Construction Of An In-Car Food And Beverage Warmer should be a summary of around 150-250 words and should highlight the main objectives, methods, results, and conclusions.
- The introduction of Design And Construction Of An In-Car Food And Beverage Warmer should provide the background information, outline the research problem, and state the objectives and significance of the study.
- Review existing research related to Design And Construction Of An In-Car Food And Beverage Warmer, identifying gaps the study aims to fill.
- The methodology section of Design And Construction Of An In-Car Food And Beverage Warmer should describe the research design, data collection methods, and analytical techniques used.
- Present the findings of the Design And Construction Of An In-Car Food And Beverage Warmer research study using tables, charts, and graphs to illustrate key points.
- Interpret Design And Construction Of An In-Car Food And Beverage Warmer results, discussing their implications, limitations, and potential areas for future research.
- Summarize the main findings of the Design And Construction Of An In-Car Food And Beverage Warmer study and restate its significance.
- List all the sources you cited in Design And Construction Of An In-Car Food And Beverage Warmer project, following a specific citation style (e.g., APA, MLA, Chicago).