The proposed system was built because of unhealthy pattern of drying of hands after washing in various restaurants and places of food selling and the rate of disease transmission such as corona virus and Ebola has prompted the need for this project. The hand dryer consists of Light Department Resistor (LDR) and 555 timer IC. The 555 timer IC is work as a monostable mode that it drives with the 5 V relay. Laser light falls on the LDR, the hand drying system remains OFF state and when the laser light is blocked by the hand from falling on the LDR, the hand drying system remains ON state. In the other words, the light from the laser module is cut off by the hand then the dryer is activated.
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
INTRODUCTION
1.1 BACKGROUND OF THE PROJECT
1.2 PROBLEM STATEMENT
1.3 OBJECTIVE OF THE PROJECT
1.4 PURPOSE OF THE PROJECT
1.5 SCOPE OF THE PROJECT
1.6 LIMITATION OF THE PROJECT
1.7 APPLICATION OF THE PROJECT
1.8 BENEFITS OF THIS DESIGN
1.9 METHODOLOGY
1.10 PROJECT ORGANISATION
CHAPTER TWO
LITERATURE REVIEW
2.1 REVIEW OF THE STUDY
2.2 REVIEW OF RELATED STUDIES
2.3 REVIEW OF DIFFERENT HAND DRYING METHOD AND THEIR ADVANTAGES
CHAPTER THREE
METHODOLOGY
3.1 SYSTEM BLOCK DIAGRAM
3.2 DESCRIPTION OF SYSTEM BLOCK
3.3 CIRCUIT DIAGRAM
3.4 CIRCUIT DESCRIPTION
3.5 COMPONENT DESCRIPTION
3.6 DESIGN CALCULATION OF DELAY TIME OF AUTOMATIC HAND DRYER
3.7 DESIGN CALCULATION OF PIN 2 OF 555 TIMER IC
CHAPTER FOUR
TEST AND RESULT ANALYSIS
4.1 INSTALLATION OF THE COMPLET DESIGN
4.2 CONSTRUCTION PROCEDURE AND TESTING
4.3 ECONOMIC OF THE PROJECT
4.4 PROJECT VIABILITY
4.5 RELIABILITY
4.6 MAINTAINABILITY
4.7 PROJECT EVALUATION
4.8 RESULT ANALYSIS
CHAPTER FIVE
5.1 CONCLUSION
5.2 RECOMMENDATION
5.3 REFERENCES
Design And Construction Of An Automatic Hand Dryer. (n.d.). UniTopics. https://www.unitopics.com/project/material/design-and-construction-of-an-automatic-hand-dryer/
“Design And Construction Of An Automatic Hand Dryer.” UniTopics, https://www.unitopics.com/project/material/design-and-construction-of-an-automatic-hand-dryer/. Accessed 26 November 2024.
“Design And Construction Of An Automatic Hand Dryer.” UniTopics, Accessed November 26, 2024. https://www.unitopics.com/project/material/design-and-construction-of-an-automatic-hand-dryer/
Here’s a typical structure for Design And Construction Of An Automatic Hand Dryer research projects:
- The title page of Design And Construction Of An Automatic Hand Dryer should include the project title, your name, institution, and date.
- The abstract of Design And Construction Of An Automatic Hand Dryer should be a summary of around 150-250 words and should highlight the main objectives, methods, results, and conclusions.
- The introduction of Design And Construction Of An Automatic Hand Dryer should provide the background information, outline the research problem, and state the objectives and significance of the study.
- Review existing research related to Design And Construction Of An Automatic Hand Dryer, identifying gaps the study aims to fill.
- The methodology section of Design And Construction Of An Automatic Hand Dryer should describe the research design, data collection methods, and analytical techniques used.
- Present the findings of the Design And Construction Of An Automatic Hand Dryer research study using tables, charts, and graphs to illustrate key points.
- Interpret Design And Construction Of An Automatic Hand Dryer results, discussing their implications, limitations, and potential areas for future research.
- Summarize the main findings of the Design And Construction Of An Automatic Hand Dryer study and restate its significance.
- List all the sources you cited in Design And Construction Of An Automatic Hand Dryer project, following a specific citation style (e.g., APA, MLA, Chicago).