This low cost automatic emergency lighting circuit turns on a lamp during power failures. It is powered by a NiCad battery that is being charged by the main power line when there is no blackout. The circuit design is very simple and can be made by almost anyone. The voltage from the step down transformer is rectified by diode D1 and filtered by C1. The NiCad battery gets charged with about 100 mA via the diode D2 and resistor R1. The battery must have a capacity of at least 2 Ah to tolerate the charging rate.
When the main power supply fails during a blackout, the charging current is interrupted and a current flows from the base of T1 via resistor R2 which triggers the transistor to conduct and the two emergency lamps light up. When the main power returns, the charging current flows again through D2 and the transistor turns the lamps off.
TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
1.0 INTRODUCTION
1.1 BACKGROUND OF THE PROJECT
- PURPOSE OF THE PROJECT
- AIM OF THE PROJECT
- OBJECTIVE OF THE PROJECT
- PURPOSE OF THE PROJECT
- LIMITATION OF THE PROJECT
- ADVANTAGES OF THE PROJECT
- PROBLEM OF THE PROJECT
- APPLICATION OF THE PROJECT
- RESEARCH QUESTION
- PROJECT ORGANISATION
CHAPTER TWO
LITERATURE REVIEW
- OVERVIEW OF THE STUDY
- REVIEW OF THE RELATED STUDY
CHAPTER THREE
3.0 CONSTRUCTION METHODOLOGY
3.1 BASIC OF THE SYSTEM
3.2 BLOCK DIAGRAM OF THE SYSTEM
3.3 SYSTEM OPERATION
3.4 CIRCUIT DIAGRAM
3.5 CIRCUIT DESCRIPTION
3.6 DESCRIPTION OF COMPONENTS USED
3.7 POWER SUPPLY UNIT
CHAPTER FOUR
4.0 TESTING AND RESULTS
- CONSTRUCTION PROCEDURE AND TESTING
- INSTALLATION OF THE COMPLET DESIGN
- ASSEMBLING OF SECTIONS
- TESTING OF SYSTEM OPERATION
- COST ANALYSIS
CHAPTER FIVE
- CONCLUSION
- RECOMMENDATION
- REFERENCES
KEYWORD: automatic emergency light circuit, automatic led emergency light project pdf, emergency light circuit board, emergency light circuit diagram free, construction of emergency light, led emergency light circuit diagram without transformer, led emergency light circuit with battery overcharge protection, emergency photo lamp, emergency light project pdf.
How does the automatic emergency light works
The voltage from the step down transformer is rectified by diode D1 and filtered by C1. The NiCad battery gets charged with about 100 mA via the diode D2 and resistor R1. The battery must have a capacity of at least 2 Ah to tolerate the charging rate.
When the main power supply fails during a blackout, the charging current is interrupted and a current flows from the base of T1 via resistor R2 which triggers the transistor to conduct and the two emergency lamps light up. When the main power returns, the charging current flows again through D2 and the transistor turns the lamps off.
The “TEST” button S1 is used to check the function of the circuit. If the secondary coil of the transformer delivers a higher voltage level, replace R1 with a higher value resistor to avoid exceeding the maximum charging current allowed for the NiCad battery being used.
Emergency light parts
- 220V to 4.5V / 2A Transformer
- D1 = 1N4004
- D2 = 1N4001
- R1 = 33Ω/1W
- R2 = 470Ω
- C1 = 470µF/16V
- T1 = 2SB242
- La1, La2 = 2.5V bulbs
- Battery = 2.5V / 2Ah Nicad
Automatic Emergency Lighting Circuit Diagram
Design And Construction Of An Automatic Emergency Light Circuit. (n.d.). UniTopics. https://www.unitopics.com/project/material/design-and-construction-of-an-automatic-emergency-light-circuit/
“Design And Construction Of An Automatic Emergency Light Circuit.” UniTopics, https://www.unitopics.com/project/material/design-and-construction-of-an-automatic-emergency-light-circuit/. Accessed 22 November 2024.
“Design And Construction Of An Automatic Emergency Light Circuit.” UniTopics, Accessed November 22, 2024. https://www.unitopics.com/project/material/design-and-construction-of-an-automatic-emergency-light-circuit/
Here’s a typical structure for Design And Construction Of An Automatic Emergency Light Circuit research projects:
- The title page of Design And Construction Of An Automatic Emergency Light Circuit should include the project title, your name, institution, and date.
- The abstract of Design And Construction Of An Automatic Emergency Light Circuit should be a summary of around 150-250 words and should highlight the main objectives, methods, results, and conclusions.
- The introduction of Design And Construction Of An Automatic Emergency Light Circuit should provide the background information, outline the research problem, and state the objectives and significance of the study.
- Review existing research related to Design And Construction Of An Automatic Emergency Light Circuit, identifying gaps the study aims to fill.
- The methodology section of Design And Construction Of An Automatic Emergency Light Circuit should describe the research design, data collection methods, and analytical techniques used.
- Present the findings of the Design And Construction Of An Automatic Emergency Light Circuit research study using tables, charts, and graphs to illustrate key points.
- Interpret Design And Construction Of An Automatic Emergency Light Circuit results, discussing their implications, limitations, and potential areas for future research.
- Summarize the main findings of the Design And Construction Of An Automatic Emergency Light Circuit study and restate its significance.
- List all the sources you cited in Design And Construction Of An Automatic Emergency Light Circuit project, following a specific citation style (e.g., APA, MLA, Chicago).