The practical importance of a battery charging unit in today’s world cannot be over emphasized. This is so since these batteries or accumulators are immensely needed by automobiles and in science laboratories. This thesis describes the methodical approach to the design and construction of any battery changer. However the procedure developed cover the construction of battery charger for battery sizes ranging from 6 volts to 12 volts.
The phototype of a battery charger for these ranges of battery has been implemented following the methodical approach as outlined in this thesis and its operational test results are quite satisfactory.
Adequate care has been taken in the design and construction to ensure that the resultant battery charger is both reliable and easy to use.
Title Page
Certification
Dedication
Acknowledgement
Abstract
Chapter One
1.0 Introduction
Chapter Two
2.0 The Storage Battery
2.1 Battery
2.2 The Storage Battery Accumulator
2.3 Nickel – Iron (Nife) Accumulator
2.4 Lead – Acid Accumulator
2.5 Active Material Of Lead – Acid Cell
2.6 Lead Peroxide (Pbv2)
2.7 Sponge Lead (Pb)
2.8 Dilute Sulphric Acid
2.9 Chemical Changes
2.10 Discharging Of A Battery
2.11 Indication Of A Fully Charged Cell
2.12 Casing
2.13 Voltage
2.14 Specification Gravity Of The Electrolyte
Chapter Three
3.0 Power Supply Unit
3.1 Component Of The Power Supply Unit
3.2 Ac – Dc Rectification
3.3 Automatic Cut Off Circuit
Chapter Four
4.0 The Battery Charging
4.1 Method Of Charging
4.2 Constant – Voltage Method
4.3 Operation Of The Charger
4.4 Battery Charger’s Casing
Chapter Five
5.0 Summary, Conclusion And Suggestion For Further Improvement
5.1 Summary
5.2 Conclusion
5.3 Cost Of Production
References
Design And Construction Of An Automatic Battery Charger ABC. (n.d.). UniTopics. https://www.unitopics.com/project/material/design-and-construction-of-an-automatic-battery-charger-abc/
“Design And Construction Of An Automatic Battery Charger ABC.” UniTopics, https://www.unitopics.com/project/material/design-and-construction-of-an-automatic-battery-charger-abc/. Accessed 21 November 2024.
“Design And Construction Of An Automatic Battery Charger ABC.” UniTopics, Accessed November 21, 2024. https://www.unitopics.com/project/material/design-and-construction-of-an-automatic-battery-charger-abc/
Here’s a typical structure for Design And Construction Of An Automatic Battery Charger ABC research projects:
- The title page of Design And Construction Of An Automatic Battery Charger ABC should include the project title, your name, institution, and date.
- The abstract of Design And Construction Of An Automatic Battery Charger ABC should be a summary of around 150-250 words and should highlight the main objectives, methods, results, and conclusions.
- The introduction of Design And Construction Of An Automatic Battery Charger ABC should provide the background information, outline the research problem, and state the objectives and significance of the study.
- Review existing research related to Design And Construction Of An Automatic Battery Charger ABC, identifying gaps the study aims to fill.
- The methodology section of Design And Construction Of An Automatic Battery Charger ABC should describe the research design, data collection methods, and analytical techniques used.
- Present the findings of the Design And Construction Of An Automatic Battery Charger ABC research study using tables, charts, and graphs to illustrate key points.
- Interpret Design And Construction Of An Automatic Battery Charger ABC results, discussing their implications, limitations, and potential areas for future research.
- Summarize the main findings of the Design And Construction Of An Automatic Battery Charger ABC study and restate its significance.
- List all the sources you cited in Design And Construction Of An Automatic Battery Charger ABC project, following a specific citation style (e.g., APA, MLA, Chicago).