The machine is designed to serve with an output of 250A. it has two pats which are the primary and secondary parts. The primary part, through which voltage is supplied to the machine has 180 turns which is made of 2mm2 S.W.G 14 copper coil. The secondary part has 45 turns made of 4mm2 S.W.G 8 copper coil.
Both turns are wound on separate limb of the laminated core. The voltage from primary turns flows to the secondary turn by induction.
The machine contain a power switch through which the machine can be switched on or off when connected to the power source. The indication light simply shows when the machine is on or off which is equally controlled by the power switch.
The fan connected to the machine helps in the looking of the temperature of the machine, it gets started once the machine is on.
The welding current is adjusted by varying the spacing between the primary and secondary windings when the cranks is rotated, clockwise the insulating block between the two winding moves down, the magnetic flux leakage and the inductive impedance are increased, thereby reducing the welding current in the secondary windings. Also as the insulating block is moved upward, away between the two turns, the magnetic flux leakage and the inductive impedance are brought down, causing the welding current to rise.
Title Page/Approval Page
Certification
Dedication
Acknowledgement
Abstract
Table Of Content
Chapter One
1.0 Introduction
1.1 Aims/Objective
1.2 Scope Or Limitation
1.3 Definition Of Terms
Chapter Two
2.0 Literature Review
2.1 Transformer Design
2.2 Coil Design
2.3 Core Design
2.4 Equivalent Circuit Of The Machine
2.5 Machine Design
2.6 Operation Of Machine
2.7 Leakage Flux Reduction
2.8 Specification From Design
Chapter Three
3.0 Construction
3.1 Lamination
3.2 Transformer Former
3.3 Copper Coil
3.4 Insulating Materials
3.5 Methodology
3.6 Casing
3.7 Coupling
3.8 Electrical Holder
Chapter Four
4.0 Testing And Finding
4.1 Open-Circuit Test
4.2 Short-Circuit Test
4.3 Test Analysis
4.4 Conditions For Operation
4.5 Cost Analysis
Chapter Five
5.0 Conclusion
5.1 Recommendation
References
Design And Construction Of An Arc Welding Machine. (n.d.). UniTopics. https://www.unitopics.com/project/material/design-and-construction-of-an-arc-welding-machine/
“Design And Construction Of An Arc Welding Machine.” UniTopics, https://www.unitopics.com/project/material/design-and-construction-of-an-arc-welding-machine/. Accessed 25 November 2024.
“Design And Construction Of An Arc Welding Machine.” UniTopics, Accessed November 25, 2024. https://www.unitopics.com/project/material/design-and-construction-of-an-arc-welding-machine/
Here’s a typical structure for Design And Construction Of An Arc Welding Machine research projects:
- The title page of Design And Construction Of An Arc Welding Machine should include the project title, your name, institution, and date.
- The abstract of Design And Construction Of An Arc Welding Machine should be a summary of around 150-250 words and should highlight the main objectives, methods, results, and conclusions.
- The introduction of Design And Construction Of An Arc Welding Machine should provide the background information, outline the research problem, and state the objectives and significance of the study.
- Review existing research related to Design And Construction Of An Arc Welding Machine, identifying gaps the study aims to fill.
- The methodology section of Design And Construction Of An Arc Welding Machine should describe the research design, data collection methods, and analytical techniques used.
- Present the findings of the Design And Construction Of An Arc Welding Machine research study using tables, charts, and graphs to illustrate key points.
- Interpret Design And Construction Of An Arc Welding Machine results, discussing their implications, limitations, and potential areas for future research.
- Summarize the main findings of the Design And Construction Of An Arc Welding Machine study and restate its significance.
- List all the sources you cited in Design And Construction Of An Arc Welding Machine project, following a specific citation style (e.g., APA, MLA, Chicago).