Design And Construction Of AC Generator Using Pulse Motor

ABSTRACT

This project is on the design and construction of pulse motor free energy generator (PMFEG). A pulsed motor, unlike normal A/C or D/C types uses short pulses of current to drive the motor, which makes it spin. This system is a new idea to generate electricity without making use of any common external sources. PMFEG conserves the input energy at high efficiency and store it and feed it back to the system and thus produces a mechanical output which can be used as a primemover. The input is given to the system using a battery, it generates pulsed and mechanical output which can be used to power an inverter that produces an ac voltage.

CHAPTER ONE

1.0                                                            INTRODUCTION

1.1                                                   BACKGROUND OF STUDY

Powering of devices consumes huge amount of energy, however this amount of energy is being reduced as the technology improves. A major limiting factor is that currently (2017) there is inadequate energy infrastructure for long routes.

The objective of the project is to make a Pulse Motor Free Energy Generator which can be used to power other devices.

It is possible to draw substantial amount of energy from the local environment and use that energy to power other devices. Not only that, but when this method of powering devices is used, the appliances gradually get conditioned to this form of non- conventional energy and their capacity for doing work increases.

Any generator requires a prime mover (such as diesel engines, water turbines etc.) to operate, that is, an external source of input is required to give an output. This external source of energy is deteriorating day by day due to excessive use

.More over this input energy once used cannot be regained back and an output that is much smaller than input is usually obtained.

This project is a new idea to generate electricity without making use of any external source. That is, we have developed a way to conserve the input energy completely and store it and feed it back to the system and thus produce a mechanical output which can be used as a prime mover. A charged battery is necessary for starting the machine. Ones it is started the power from the machine is fed back to recharge the battery and this process continuous. Hence, the output is far greater than the input provided which results in great efficiency.

Two different kinds of energies involved in the process can be carefully distinguished and manipulated for practical advantages in powering various loads. The Pulse Motor Free Energy Generator is a decent, powerful and well-looking topology of a free energy generator.

Free energy has two meanings:

1. Energy that can be obtained from a device at low
2. More output energy that appears to be available than input

The Law of Conservation of Energy is generally thought to be correct when it states that more energy cannot be taken out of any system than is put into that system. However, that does not mean that we cannot get more energy out of a system than we put into it. The Pulse Motor Free Energy Generator is a device that demonstrates this free energy concept on a small scale .It will generate the required electric power with less input. The main aim of this work is to use pulse motor to generate a 220v ac.

1.2                                                    PROBLEM STATEMENT

In the past, energy generation depends fully on fossil fuels which produces carbon monoxide and also have higher cost power generation bill. Because of these disadvantages, researchers came out with free energy generation. Free energy sources of energy are now a major concern worldwide as replacement to the high demand of fossil fuels. This energy becomes free only at a point after which we don’t have to pay for power generation after commissioning the unit. By using the pulse motor continuous motion (Energy) is generated.

1.3                                                  AIM OF THE STUDY

The aim of this work is to build a system that uses pulse motor to generate 220v alternating current.

1.4                                           OBJESCTIVE OF THE STUDY

The objective of the study is to provide a system for driving a pulse motor which eliminates undesirable step motions at low speeds, compensates insufficient torque due to the inductance of the exciting coils at high speeds, and improves the driving characteristics of the motor at both high and low speeds. The other objective of the study is to provide a system for driving a pulse motor which provides poly-phase trapezoid exciting signals required for continuous rotation of the pulse motor.

1.5                                                SCOPE OF THE STUDY

The pulse motor is driven by precise synchronization with command pulses. Therefore, the pulse motor can constitute a high accuracy servo-system with open loops. However, because the revolution of the pulse motor is carried out stepwise, the discontinuity of revolutions is remarkable especially when the motor is driven at low speeds. Further, as the pulse motor is driven by pulses, the driving torque at high speeds becomes insufficient, because inductances of the exciting coils deteriorate the rising time of the exciting current.

SIGNIFICANCE OF THE STUDY

The output appears to be far greater than the input provided which results in greater efficiency. Hence the pulse motor free energy generator is a decent, powerful, low cost, high efficient and well-looking topology of a free energy generator, which can be used to power an inerter that powers other ac appliances.

1.6                                                        METHODOLOGY

To achieve the aim and objectives of this work, the following are the steps involved:

1. Study of the previous work on the project so as to improve it efficiency.
2. Draw a block diagram.

• Test for continuity of components and devices,

1. Design and calculation for the work was carried out.
2. Studying of various component used in circuit.
3. The setup of the system circuit.

• Finally, the whole device was cased and final test was carried out.

1.7                                                         PROJECT ORGANISATION

The work is organized as follows: chapter one discuses the introductory part of the work, chapter two presents the literature review of the study, chapter three describes the methods applied, chapter four discusses the results of the work, chapter five summarizes the research outcomes and the recommendations.