ABSTRACT
Multicell charger is a battery charging device, which can safely charge up to two pieces of Ni-Cd cells or Ni-MH cells. The circuit is compact, inexpensive and easy-to-use. The 230V AC mains is down-converted to 12V AC (at 500 mA) by step-down transformer X1, converted into pulsating DC voltage by diodes D1 and D2, and fed to the battery charger terminals via current-limiting resistor R1 and silicon-controlled rectifier SCR1.
SCR1 is at the heart of the charger. Normally, it conducts due to the gate biasing voltage available through resistor R2 and diode D3, and the battery is in charging mode, which is indicated by LED1. Resistor R2 limits the charging current to a safe value. Charging current of this circuit is about 250 mA.
When the battery reaches full charge, SCR2 conducts to pull down the gate of SCR1. This state is indicated by LED2.
TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
1.0 INTRODUCTION
1.1 BACKGROUND OF THE PROJECT
- PURPOSE OF THE PROJECT
- AIM OF THE PROJECT
- OBJECTIVE OF THE PROJECT
- PURPOSE OF THE PROJECT
- LIMITATION OF THE PROJECT
- ADVANTAGES OF THE PROJECT
- PROBLEM OF THE PROJECT
- APPLICATION OF THE PROJECT
- RESEARCH QUESTION
- PROJECT ORGANISATION
CHAPTER TWO
LITERATURE REVIEW
- OVERVIEW OF THE STUDY
- REVIEW OF THE RELATED STUDY
CHAPTER THREE
3.0 CONSTRUCTION METHODOLOGY
3.1 BASIC OF THE SYSTEM
3.2 BLOCK DIAGRAM OF THE SYSTEM
3.3 SYSTEM OPERATION
3.4 CIRCUIT DIAGRAM
3.5 CIRCUIT DESCRIPTION
3.6 DESCRIPTION OF COMPONENTS USED
3.7 POWER SUPPLY UNIT
CHAPTER FOUR
4.0 TESTING AND RESULTS
- CONSTRUCTION PROCEDURE AND TESTING
- INSTALLATION OF THE COMPLET DESIGN
- ASSEMBLING OF SECTIONS
- TESTING OF SYSTEM OPERATION
- COST ANALYSIS
CHAPTER FIVE
- CONCLUSION
- RECOMMENDATION
- REFER
Design And Construction Of A Multicell Charger. (n.d.). UniTopics. https://www.unitopics.com/project/material/design-and-construction-of-a-multicell-charger/
“Design And Construction Of A Multicell Charger.” UniTopics, https://www.unitopics.com/project/material/design-and-construction-of-a-multicell-charger/. Accessed 22 November 2024.
“Design And Construction Of A Multicell Charger.” UniTopics, Accessed November 22, 2024. https://www.unitopics.com/project/material/design-and-construction-of-a-multicell-charger/
Here’s a typical structure for Design And Construction Of A Multicell Charger research projects:
- The title page of Design And Construction Of A Multicell Charger should include the project title, your name, institution, and date.
- The abstract of Design And Construction Of A Multicell Charger should be a summary of around 150-250 words and should highlight the main objectives, methods, results, and conclusions.
- The introduction of Design And Construction Of A Multicell Charger should provide the background information, outline the research problem, and state the objectives and significance of the study.
- Review existing research related to Design And Construction Of A Multicell Charger, identifying gaps the study aims to fill.
- The methodology section of Design And Construction Of A Multicell Charger should describe the research design, data collection methods, and analytical techniques used.
- Present the findings of the Design And Construction Of A Multicell Charger research study using tables, charts, and graphs to illustrate key points.
- Interpret Design And Construction Of A Multicell Charger results, discussing their implications, limitations, and potential areas for future research.
- Summarize the main findings of the Design And Construction Of A Multicell Charger study and restate its significance.
- List all the sources you cited in Design And Construction Of A Multicell Charger project, following a specific citation style (e.g., APA, MLA, Chicago).