This geyser timer circuit sounds an alarm after the set timing of 22 minutes when the water is heated up and can be used. The circuit comprises a timer IC 555 wired as an astable multivibrator with adjustable time period of 15 seconds. The astable output after inversion by an inverter drives decade counters IC3 and IC4 (each IC 7490) connected in cascade. The decade counters output is connected to decoders IC5 and IC6 (each IC 7442), respectively. The decoder outputs (Q8 outputs of IC5 and IC6) are fed to inverters and the inverter outputs, in turn, are fed to an AND gate. The AND output is connected to the reset pin of the astable multivibrator built around another timer IC 555 to sound the alarm.
TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
1.0 INTRODUCTION
1.1 BACKGROUND OF THE PROJECT
- PURPOSE OF THE PROJECT
- AIM OF THE PROJECT
- OBJECTIVE OF THE PROJECT
- PURPOSE OF THE PROJECT
- LIMITATION OF THE PROJECT
- ADVANTAGES OF THE PROJECT
- PROBLEM OF THE PROJECT
- APPLICATION OF THE PROJECT
- RESEARCH QUESTION
- PROJECT ORGANISATION
CHAPTER TWO
LITERATURE REVIEW
- OVERVIEW OF THE STUDY
- REVIEW OF THE RELATED STUDY
CHAPTER THREE
3.0 CONSTRUCTION METHODOLOGY
3.1 BASIC OF THE SYSTEM
3.2 BLOCK DIAGRAM OF THE SYSTEM
3.3 SYSTEM OPERATION
3.4 CIRCUIT DIAGRAM
3.5 CIRCUIT DESCRIPTION
3.6 DESCRIPTION OF COMPONENTS USED
3.7 POWER SUPPLY UNIT
CHAPTER FOUR
4.0 TESTING AND RESULTS
- CONSTRUCTION PROCEDURE AND TESTING
- INSTALLATION OF THE COMPLET DESIGN
- ASSEMBLING OF SECTIONS
- TESTING OF SYSTEM OPERATION
- COST ANALYSIS
CHAPTER FIVE
- CONCLUSION
- RECOMMENDATION
- REFERENCES
KEYWORD: geyser timer, geyser circuit diagram, timer circuits, electric geyser wiring diagram, how to use geyser, geyser connection diagram, 555 timer projects, timer circuit using 555, advanced 555 timer projects.
Geyser timer circuit
The circuit comprises a timer IC 555 wired as an astable multivibrator with adjustable time period of 15 seconds. The astable output after inversion by an inverter drives decade counters IC3 and IC4 (each IC 7490) connected in cascade. The decade counters output is connected to decoders IC5 and IC6 (each IC 7442), respectively. The decoder outputs (Q8 outputs of IC5 and IC6) are fed to inverters and the inverter outputs, in turn, are fed to an AND gate. The AND output is connected to the reset pin of the astable multivibrator built around another timer IC 555 to sound the alarm. Now you can turn off the geyser.
A green LED (LED1) has been used as the power supply indicator.
Switch on the timer and the geyser at the same time. When the alarm sounds, it means that the water in the geyser has heated up and can be used.
Geyser timer circuit
Construction & testing
Advertisement
You can assemble the timer circuit on a general-purpose PCB and install it near your bathroom so that both the timer circuit and the geyser can be switched on simultaneously.
After the siren sounds, if required, we can increase the time by another 22 minutes for geyser by resetting the circuit by pushing reset switches S1 and S2 momentarily.
If you want to change the preset time of the geyser, the same can be easily done by combining appropriate outputs of IC5 and IC6 using DIP switches (S3 and S4) while keeping in mind IC5 outputs (Q0 through Q9) are spaced 15 seconds apart and IC6 outputs are spaced 150 seconds (2.5 minutes) apart.
Caution
Please note that the timer circuit has no connection with the geyser circuit. The geyser works off 220V AC, while the timer works off 5V DC.
Design And Construction Of A Geyser Timer. (n.d.). UniTopics. https://www.unitopics.com/project/material/design-and-construction-of-a-geyser-timer/
“Design And Construction Of A Geyser Timer.” UniTopics, https://www.unitopics.com/project/material/design-and-construction-of-a-geyser-timer/. Accessed 22 November 2024.
“Design And Construction Of A Geyser Timer.” UniTopics, Accessed November 22, 2024. https://www.unitopics.com/project/material/design-and-construction-of-a-geyser-timer/
Here’s a typical structure for Design And Construction Of A Geyser Timer research projects:
- The title page of Design And Construction Of A Geyser Timer should include the project title, your name, institution, and date.
- The abstract of Design And Construction Of A Geyser Timer should be a summary of around 150-250 words and should highlight the main objectives, methods, results, and conclusions.
- The introduction of Design And Construction Of A Geyser Timer should provide the background information, outline the research problem, and state the objectives and significance of the study.
- Review existing research related to Design And Construction Of A Geyser Timer, identifying gaps the study aims to fill.
- The methodology section of Design And Construction Of A Geyser Timer should describe the research design, data collection methods, and analytical techniques used.
- Present the findings of the Design And Construction Of A Geyser Timer research study using tables, charts, and graphs to illustrate key points.
- Interpret Design And Construction Of A Geyser Timer results, discussing their implications, limitations, and potential areas for future research.
- Summarize the main findings of the Design And Construction Of A Geyser Timer study and restate its significance.
- List all the sources you cited in Design And Construction Of A Geyser Timer project, following a specific citation style (e.g., APA, MLA, Chicago).