Wooden-case, battery-operated wall clocks with pendulums are available in the market. Some even have chimes. What is missing is the tick-tock sound of old mechanical pendulum clocks. This work is on a tick-tock sound generator. It is built around timer IC 7555 (IC1) wired as an astable multivibrator. Resistor R1, preset VR1 and capacitor C1 generate frequencies that can be varied with the help of preset VR1. At output pin 3 of IC1, a small speaker is connected via capacitor C3 that produces the tick-tock sound.
TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
1.0 INTRODUCTION
1.1 BACKGROUND OF THE PROJECT
- PURPOSE OF THE PROJECT
- AIM OF THE PROJECT
- OBJECTIVE OF THE PROJECT
- PURPOSE OF THE PROJECT
- LIMITATION OF THE PROJECT
- ADVANTAGES OF THE PROJECT
- PROBLEM OF THE PROJECT
- APPLICATION OF THE PROJECT
- RESEARCH QUESTION
- PROJECT ORGANISATION
CHAPTER TWO
LITERATURE REVIEW
- OVERVIEW OF THE STUDY
- REVIEW OF THE RELATED STUDY
CHAPTER THREE
3.0 CONSTRUCTION METHODOLOGY
3.1 BASIC OF THE SYSTEM
3.2 BLOCK DIAGRAM OF THE SYSTEM
3.3 SYSTEM OPERATION
3.4 CIRCUIT DIAGRAM
3.5 CIRCUIT DESCRIPTION
3.6 DESCRIPTION OF COMPONENTS USED
3.7 POWER SUPPLY UNIT
CHAPTER FOUR
4.0 TESTING AND RESULTS
- CONSTRUCTION PROCEDURE AND TESTING
- INSTALLATION OF THE COMPLET DESIGN
- ASSEMBLING OF SECTIONS
- TESTING OF SYSTEM OPERATION
- COST ANALYSIS
CHAPTER FIVE
- CONCLUSION
- RECOMMENDATION
- REFERENCES
Keyword: clock tick-tock sound generator and led pendulum, electronic circuits projects diagrams free, 555 and 4017 circuits, 4017 ic projects, mini project using ic, 555 timer projects, circuit today 555 timer, cd4017 vu meter, alarm circuit using timer 555.
Tick-tock sound generator circuit
Circuit of tick-tock sound generator Wooden clock design
Shown above is the circuit of a tick-tock sound generator. It is built around timer IC 7555 (IC1) wired as an astable multivibrator. Resistor R1, preset VR1 and capacitor C1 generate frequencies that can be varied with the help of preset VR1. At output pin 3 of IC1, a small speaker is connected via capacitor C3 that produces the tick-tock sound. At pin 3 of IC1, two yellow LEDs are also connected on the clock face to flash in time with sound (see Fig. 2). Adjust preset VR1 such that ticking sound closely resembles the tick-tock of old pendulum clocks. Yellow LEDs (LED1 and LED2) match well with the wooden clock.
LED pendulum circuit
Shown below is the circuit for the LED pendulum. It uses another timer 7555 wired in astable mode and its clock pulse at pin 3 is fed to clock pin 14 of decade counter 4017 (IC3). The outputs of IC3 are connected with the help of switching diode 1N4148 such that the six LEDs (LED3 through LED8) flash in sequence in one direction first and then in reverse sequence. The speed of flashing of LEDs can be adjusted with the help of 10-kilo-ohm preset VR2. Capacitor C6 (6.8nF) and resistor R11 (100-kilo-ohm) are used to reset the decade counter.
Circuit for LED pendulum
Construction & testing
Assemble the circuit on a general-purpose PCB and enclose in a suitable cabinet. Mount the LEDs either in ‘V’ shape or ‘U’ shape on the front panel of the cabinet (as shown in Fig. 4).
Design And Construction Of A Clock Tick-Tock Sound Generator And Led Pendulum. (n.d.). UniTopics. https://www.unitopics.com/project/material/design-and-construction-of-a-clock-tick-tock-sound-generator-and-led-pendulum/
“Design And Construction Of A Clock Tick-Tock Sound Generator And Led Pendulum.” UniTopics, https://www.unitopics.com/project/material/design-and-construction-of-a-clock-tick-tock-sound-generator-and-led-pendulum/. Accessed 23 November 2024.
“Design And Construction Of A Clock Tick-Tock Sound Generator And Led Pendulum.” UniTopics, Accessed November 23, 2024. https://www.unitopics.com/project/material/design-and-construction-of-a-clock-tick-tock-sound-generator-and-led-pendulum/
Here’s a typical structure for Design And Construction Of A Clock Tick-Tock Sound Generator And Led Pendulum research projects:
- The title page of Design And Construction Of A Clock Tick-Tock Sound Generator And Led Pendulum should include the project title, your name, institution, and date.
- The abstract of Design And Construction Of A Clock Tick-Tock Sound Generator And Led Pendulum should be a summary of around 150-250 words and should highlight the main objectives, methods, results, and conclusions.
- The introduction of Design And Construction Of A Clock Tick-Tock Sound Generator And Led Pendulum should provide the background information, outline the research problem, and state the objectives and significance of the study.
- Review existing research related to Design And Construction Of A Clock Tick-Tock Sound Generator And Led Pendulum, identifying gaps the study aims to fill.
- The methodology section of Design And Construction Of A Clock Tick-Tock Sound Generator And Led Pendulum should describe the research design, data collection methods, and analytical techniques used.
- Present the findings of the Design And Construction Of A Clock Tick-Tock Sound Generator And Led Pendulum research study using tables, charts, and graphs to illustrate key points.
- Interpret Design And Construction Of A Clock Tick-Tock Sound Generator And Led Pendulum results, discussing their implications, limitations, and potential areas for future research.
- Summarize the main findings of the Design And Construction Of A Clock Tick-Tock Sound Generator And Led Pendulum study and restate its significance.
- List all the sources you cited in Design And Construction Of A Clock Tick-Tock Sound Generator And Led Pendulum project, following a specific citation style (e.g., APA, MLA, Chicago).