A battery charger is an electrical device employed for charging batteries. These batteries that are usually charged by battery charger are the storage batteries also known as “accumulator” the battery charger changes. The alternating current forms the power line into d.c suitable for charging.
When the battery is fully changed, is up to it’s maximum, 12 volt, the charger with automatically cut-off with the help of the contact relay, the transistor and the zener diode when bend the current back to the system, and the system have the ability to indicate when the battery is charging or not, when the battery is empty or fully charged.
Cover page
ii. Certification
iii. Dedication
iv. Acknowledgement
v. Abstract:
CHAPTER ONE
INTRODUCTION
1.1 Background of the Study
1.2 Problem Statement
1.3 Hypothesis/Research Questions
1.4 Objective of Study
1.5 Significance of Study
1.6 Scope of Study
1.7 Limitations of Study
1.8 Definitions of terms
CHAPTER TWO
LITERATURE REVIEW
2.1 Review of Related works
2.2 Contribution to Knowledge
2.3 Proposed system’s Theories
2.4 Expected Results from Hardware &Software
CHAPTER THREE
DESIGN METHODOLOGY
3.1 The Block Diagram of a Battery Charger
3.2 System Circuit
3.3 System Operation
3.4 Circuit Description
CHAPTER FOUR
RESULTS/ANALYSIS
4.1 CONSTRUCTION PROCEDURE AND TESTING ANALYSIS
4.2 Casing And Packaging
4.3 Assembling Of Sections
4.4 Tests an Operation
4.5 Battery Charger Casing
CHAPTER FIVE
SUMMARY,CONCLUSION AND RECONMENDATIONS
5.1 Summary
5.2 Conclusion
5.3 Recommendation
References
Design And Construction Of A Battery Charger With Over-Charge Cut-Off. (n.d.). UniTopics. https://www.unitopics.com/project/material/design-and-construction-of-a-battery-charger-with-over-charge-cut-off/
“Design And Construction Of A Battery Charger With Over-Charge Cut-Off.” UniTopics, https://www.unitopics.com/project/material/design-and-construction-of-a-battery-charger-with-over-charge-cut-off/. Accessed 21 November 2024.
“Design And Construction Of A Battery Charger With Over-Charge Cut-Off.” UniTopics, Accessed November 21, 2024. https://www.unitopics.com/project/material/design-and-construction-of-a-battery-charger-with-over-charge-cut-off/
Here’s a typical structure for Design And Construction Of A Battery Charger With Over-Charge Cut-Off research projects:
- The title page of Design And Construction Of A Battery Charger With Over-Charge Cut-Off should include the project title, your name, institution, and date.
- The abstract of Design And Construction Of A Battery Charger With Over-Charge Cut-Off should be a summary of around 150-250 words and should highlight the main objectives, methods, results, and conclusions.
- The introduction of Design And Construction Of A Battery Charger With Over-Charge Cut-Off should provide the background information, outline the research problem, and state the objectives and significance of the study.
- Review existing research related to Design And Construction Of A Battery Charger With Over-Charge Cut-Off, identifying gaps the study aims to fill.
- The methodology section of Design And Construction Of A Battery Charger With Over-Charge Cut-Off should describe the research design, data collection methods, and analytical techniques used.
- Present the findings of the Design And Construction Of A Battery Charger With Over-Charge Cut-Off research study using tables, charts, and graphs to illustrate key points.
- Interpret Design And Construction Of A Battery Charger With Over-Charge Cut-Off results, discussing their implications, limitations, and potential areas for future research.
- Summarize the main findings of the Design And Construction Of A Battery Charger With Over-Charge Cut-Off study and restate its significance.
- List all the sources you cited in Design And Construction Of A Battery Charger With Over-Charge Cut-Off project, following a specific citation style (e.g., APA, MLA, Chicago).