ABSTRACT
This project is on a 12 volts automatic battery charger with charging progress and charging level indicator. An automatic battery charger is an acid battery charger that is designed to charge any acid battery.
In this work, a voltage sensor circuit is incorporated to sense the voltage of the battery under charge. The charger has the ability to automatically switch OFF when the battery voltage reaches the required optimum level with the help of the contact relay, the transistor and the zener diode when bend the current back to the system, and the system have the ability to indicate when the battery is charging or not, when the battery is empty or fully charged.
TABLE OF CONTENTS
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWLEDGEMENT
ABSTRACT
TABLE OF CONTENT
CHAPTER ONE
- INTRODUCTION
- AIM/OBJECTIVE OF THE PROJECT
- SIGNIFICANCE OF THE PROJECT
- APPLICATION OF THE PROJECT
- LIMITATION OF THE PROJECT
- ADVANTAGES OF AUTOMATIC CHARGER
- FEATURES OF AUTOMATIC BATTERY CHARGER
- PROJECT ORGANIZATION
CHAPTER TWO
LITERATURE REVIEW
2.1 REVIEW OF BATTERY CHARGER
2.2 HISTORICAL BACKGROUND OF BATTERY CHARGER
2.3 REVIEW OF RECHARGEABLE BATTERY
2.4 REVIEW OF CHARGER UNITS
2.4.1 SUPPLY UNIT
2.4.2 THE RECTIFYING UNIT
2.4.3 THE SMOOTHING UNIT
2.4.4 THE REGULATOR AND REGULATED
2.4.5 D.C CHARGING UNIT
CHAPTER THREE
3.0 CONSTRUCTION METHODOLOGY
3.1 BLOCK DIAGRAM OF THE SYSTEM
3.2 CIRCUIT DIAGRAM
3.3 CIRCUIT DESCRIPTION
3.4 SYSTEM OPERATION
3.5 DESCRIPTION OF MAJOR COMPONENTS USED
CHAPTER FOUR
4.1 RESULT ANALYSIS
4.1 CONSTRUCTION PROCEDURE AND TESTING
4.2 CASING AND PACKAGING
4.3 ASSEMBLING OF SECTIONS
4.4 TESTING OF SYSTEM OPERATION OBSERVATIONS
4.6 DIFFICULTIES ENCOUNTERED ON THE SYSTEM
4.7 COST OF PRODUCTION
CHAPTER FIVE
- SUMMARY
- CONCLUSIONS/SUGGESTIONS
5.3 REFERENCES
CHAPTER ONE
1.1 INTRODUCTION
A battery charger is an electrical device employed in charging batteries that are usually charged by battery charges are the storage batteries also known as “accumulators”.
The charger is made up of various electrical and electronics component which for the purpose of clanty are group into your basic unit they are:
The power supply units
The smoothing circuits
The regulating unit and
Regulated D.C charging units
A Battery charger comes in various designs and voltage. The choice of a particular and of charger that depends largely int eh size of battery or battery or batteries which on mterds to charge the mini battery changer could be used to charge batteries whose voltage ranges from 6 – 12 volts. The bigger battery changes are for batteries with voltage ranging from 12 – 48 volts. These are the heavy duty batteries.
The battery charge is built in such a way that it delivers a constant value of d.c current into the battery it is charging in the opposite direction from which current flows on the batteries during discharge one cannot successfully design a battery charge with out a fundamental understanding of the accumulator because it also makes up the operation.
1.2 OBJECTIVES OF THE PROJECT
The objective of the project is to design a device that will recharge 12v lead acid battery when discharged. The device has the ability to indicate charging process, low battery and fully charge levels through LED indicators.
1.3 SIGNIFICANCE OF THE PROJECT
This device charges 12v acid battery mainly, however, if the output voltages are adjusted can be used to charge battery of lower or higher voltages. Apart from charging batteries, this device can also be used as a battery level monitor due to the battery level feature it contains.
1.4 APPLICATION OF THE PROJECT
Battery charger is used in the following devices for the purpose of recharging device batteries:
- It is used in inverter
- It is used in cellphone
- It is used in Solar energy system
- It is used in vehicles
- It is used in an uninterruptible power supply(UPS), etc.
1.5 LIMITATION OF THE PROJECT
The only problem with this device is that it takes longer time to recharge car battery because of the low current output, and it is design only for a 12 battery.
1.6 ADVANTAGES OF AUTOMATIC CHARGER
Features of this automatic battery charger made it more advantageous than other types and they are as below:
- Automatic battery charger has an indicator to indicate when the battery is fully charged
- Built in Indications for showing Full, Empty Levels of any type of battery
- It has a manually operated switch that is used to ON and OFF the entire system.
- It composes of in-built active components which stop charging process when the battery is fully charged.
- It consumed less current but generate high current to the load.
1.7 FEATURE AND BLOCK OF CHARGER
A battery charger is an electrical device employed in charging batteries that are usually charged by battery charges are the storage batteries also known as “accumulators”.
The charger is made up of various electrical and electronics component which for the purpose of charging are group into your basic unit, they are:
The power supply units
The smoothing circuits
The regulating unit and
Regulated D.C charging units
A Battery charger comes in various designs and voltage. The choice of a particular and of charger that depends largely in Ah size of battery or batteries which charge the mini battery changer could be used to charge batteries whose voltage ranges from 6 – 12 volts. The bigger battery changes are for batteries with voltage ranging from 12 – 48 volts. These are the heavy duty batteries.
The battery charge is built in such a way that it delivers a constant value of d.c current into the battery it is charging in the opposite direction from which current flows on the batteries during discharge one cannot successfully design a battery charge without a fundamental understanding of the accumulator because it also makes up the operation.
1.8 PROJECT WORK ORGANIZATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this work is on the introduction to a 12v battery charger. In this chapter, the background, significance, objective limitation and problem of a 12v battery charger were discussed.
Chapter two is on literature review of a 12v battery charger. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.
Design And Construction Of A 12 Volts Automatic Battery Charger With Charging Progress And Charging Level Indicator. (n.d.). UniTopics. https://www.unitopics.com/project/material/design-and-construction-of-a-12-volts-automatic-battery-charger-with-charging-progress-and-charging-level-indicator/
“Design And Construction Of A 12 Volts Automatic Battery Charger With Charging Progress And Charging Level Indicator.” UniTopics, https://www.unitopics.com/project/material/design-and-construction-of-a-12-volts-automatic-battery-charger-with-charging-progress-and-charging-level-indicator/. Accessed 22 November 2024.
“Design And Construction Of A 12 Volts Automatic Battery Charger With Charging Progress And Charging Level Indicator.” UniTopics, Accessed November 22, 2024. https://www.unitopics.com/project/material/design-and-construction-of-a-12-volts-automatic-battery-charger-with-charging-progress-and-charging-level-indicator/
Here’s a typical structure for Design And Construction Of A 12 Volts Automatic Battery Charger With Charging Progress And Charging Level Indicator research projects:
- The title page of Design And Construction Of A 12 Volts Automatic Battery Charger With Charging Progress And Charging Level Indicator should include the project title, your name, institution, and date.
- The abstract of Design And Construction Of A 12 Volts Automatic Battery Charger With Charging Progress And Charging Level Indicator should be a summary of around 150-250 words and should highlight the main objectives, methods, results, and conclusions.
- The introduction of Design And Construction Of A 12 Volts Automatic Battery Charger With Charging Progress And Charging Level Indicator should provide the background information, outline the research problem, and state the objectives and significance of the study.
- Review existing research related to Design And Construction Of A 12 Volts Automatic Battery Charger With Charging Progress And Charging Level Indicator, identifying gaps the study aims to fill.
- The methodology section of Design And Construction Of A 12 Volts Automatic Battery Charger With Charging Progress And Charging Level Indicator should describe the research design, data collection methods, and analytical techniques used.
- Present the findings of the Design And Construction Of A 12 Volts Automatic Battery Charger With Charging Progress And Charging Level Indicator research study using tables, charts, and graphs to illustrate key points.
- Interpret Design And Construction Of A 12 Volts Automatic Battery Charger With Charging Progress And Charging Level Indicator results, discussing their implications, limitations, and potential areas for future research.
- Summarize the main findings of the Design And Construction Of A 12 Volts Automatic Battery Charger With Charging Progress And Charging Level Indicator study and restate its significance.
- List all the sources you cited in Design And Construction Of A 12 Volts Automatic Battery Charger With Charging Progress And Charging Level Indicator project, following a specific citation style (e.g., APA, MLA, Chicago).