The aim of this project was to construct shell and tube heat exchanger with fixed boundless. A heat exchanger that would cool 5 x 5 x 10 – 3 kg/s of steam at a calculated heat load of 152 – 395/S was fabricated. The steam is to reach the heat exchanger from a distillation column at a temperature of 300k. The specification of the layout as well as the detailed mechanical design were assumed and also calculated.
It is established that a horizontal heat exchanger with cold water at the shall side and the treated steam at the tube side is adequate for this operation, with the aim of cooling the steam from the distillation column.
The available area obtained from calculation is 1.0m2 and also the overall heat transfer coefficient obtained is 4.10W/M2k. it is also seen that the heat exchanger is satisfactory and consists of five copper tubes of inside diameter 90mm and 5920mm length. The shell inside diameter 810mm and 5.770mm length. The tube and shell heat exchanger has a total length of 5820mm.
The material of construction for the shell side is stainless steel while copper tubes were used for the tubes inside.
The total cost of the heat exchanger was N12,000.
Title Page
Approval page
Letter of transmitted
Dedication
Acknowledgements
Abstract
Table of contents
CHAPTER ONE
1.1 Introduction
CHAPTER TWO
2.0 Literature Review
2.1 General Design of Heat Exchanger
2.2 Tubular Heat Exchanger
2.3 Design Description of the Major Components
2.4 Tubes
2.5 Tube Bundles
2.6 Shells
2.7 Baffle
2.8 Tie Road Spacers
2.9 Pass Partition Plates
CHAPTER THREE
3.0 Fabrication Procedures
3.1 Dimensioning and Marking Out
3.2 Cutting
3.3 Folding or Rolling
3.4 Drilling operation
3.5 Assembling Process
3.6 Welding Operation
3.7 Filling
3.8 Dimensions and Parameters Derived
3.9 From the Fabrication Units
CHAPTER FOUR
4.0 Costing
CHAPTER FIVE
5.0 Discussion
CHAPTER SIX
6.0 Conclusion
6.1 Recommendations
CHAPTER SEVEN
7.0 Notation and Nomenclature
References
Appendix
Physical Properties of Water
Calculation of the Head Load
Construction Of Shell And Tube Heat Exchanger. (n.d.). UniTopics. https://www.unitopics.com/project/material/construction-of-sheel-and-tube-heat-exchanger/
“Construction Of Shell And Tube Heat Exchanger.” UniTopics, https://www.unitopics.com/project/material/construction-of-sheel-and-tube-heat-exchanger/. Accessed 24 November 2024.
“Construction Of Shell And Tube Heat Exchanger.” UniTopics, Accessed November 24, 2024. https://www.unitopics.com/project/material/construction-of-sheel-and-tube-heat-exchanger/
Here’s a typical structure for Construction Of Shell And Tube Heat Exchanger research projects:
- The title page of Construction Of Shell And Tube Heat Exchanger should include the project title, your name, institution, and date.
- The abstract of Construction Of Shell And Tube Heat Exchanger should be a summary of around 150-250 words and should highlight the main objectives, methods, results, and conclusions.
- The introduction of Construction Of Shell And Tube Heat Exchanger should provide the background information, outline the research problem, and state the objectives and significance of the study.
- Review existing research related to Construction Of Shell And Tube Heat Exchanger, identifying gaps the study aims to fill.
- The methodology section of Construction Of Shell And Tube Heat Exchanger should describe the research design, data collection methods, and analytical techniques used.
- Present the findings of the Construction Of Shell And Tube Heat Exchanger research study using tables, charts, and graphs to illustrate key points.
- Interpret Construction Of Shell And Tube Heat Exchanger results, discussing their implications, limitations, and potential areas for future research.
- Summarize the main findings of the Construction Of Shell And Tube Heat Exchanger study and restate its significance.
- List all the sources you cited in Construction Of Shell And Tube Heat Exchanger project, following a specific citation style (e.g., APA, MLA, Chicago).