The practical importance of a battery charger in today world cannot be over emphasized. This is so as those batteries accumulators are immensely needed by out auto mobile and in science laboratories.
This thesis describes the methodical approach to the design and construction of any battery charger. However the procedure fro developed cover the construction of battery charger for battery sizes ranging from 6 voltage to 24volatge (heavy duty) batteries.
The prototype of a battery charger for these ranges of batteries has been implemented following the methodical approach as outlined in this thesis and its operational test results are quite satisfactory. adequate care has been taken in the design and construction to ensure that the resultant battery charger are both reliable and easy to use.
Title Page
Approval Page
Dedication
Acknowledgement
Abstract
Chapter One
1.0 Introduction
1.1 Background Of The Project
1.2 Aim And Objective
1.3 Scope Of The Project
1.4 Organization Of The Project
Chapter Two
2.0 Literature Review
2.1 Battery
2.2 The Storage Battery
2.2.1 Nikel Iron Battery
2.2.2 Lead Acid Battery
2.3 Indications Of A Fully Charged Cell
2.3.1 Gassing
2.3.2 Voltage
2.3.3 Colour
2.3.4 Charger
Chapter Three
3.1 Function Block Diagram
3.1.1 Power Supply Unit
3.1.2 Ac To Dc Rectification
3.1.3 Filter And Regulation
3.2 Types Of Carrging System
3.2.1 Half Wave System
3.2.2 Full Wave Charging System
Chapter Four
4.1 Construction Of Battery Charger
4.1.1 Power Supply Unit (Psu)
4.1.2 Detector Circuit
4.2 Components Of A Psu
4.3 Components Of Detector Circuit
Chapter Five
5.1 Summary
5.2 Conclusion
5.3 Component Sourcing
References
Construction Of A Battery Changer Using Silicon Controlled Regulator SCR. (n.d.). UniTopics. https://www.unitopics.com/project/material/construction-of-a-battery-changer-using-silicon-controlled-regulator-scr/
“Construction Of A Battery Changer Using Silicon Controlled Regulator SCR.” UniTopics, https://www.unitopics.com/project/material/construction-of-a-battery-changer-using-silicon-controlled-regulator-scr/. Accessed 24 November 2024.
“Construction Of A Battery Changer Using Silicon Controlled Regulator SCR.” UniTopics, Accessed November 24, 2024. https://www.unitopics.com/project/material/construction-of-a-battery-changer-using-silicon-controlled-regulator-scr/
Here’s a typical structure for Construction Of A Battery Changer Using Silicon Controlled Regulator SCR research projects:
- The title page of Construction Of A Battery Changer Using Silicon Controlled Regulator SCR should include the project title, your name, institution, and date.
- The abstract of Construction Of A Battery Changer Using Silicon Controlled Regulator SCR should be a summary of around 150-250 words and should highlight the main objectives, methods, results, and conclusions.
- The introduction of Construction Of A Battery Changer Using Silicon Controlled Regulator SCR should provide the background information, outline the research problem, and state the objectives and significance of the study.
- Review existing research related to Construction Of A Battery Changer Using Silicon Controlled Regulator SCR, identifying gaps the study aims to fill.
- The methodology section of Construction Of A Battery Changer Using Silicon Controlled Regulator SCR should describe the research design, data collection methods, and analytical techniques used.
- Present the findings of the Construction Of A Battery Changer Using Silicon Controlled Regulator SCR research study using tables, charts, and graphs to illustrate key points.
- Interpret Construction Of A Battery Changer Using Silicon Controlled Regulator SCR results, discussing their implications, limitations, and potential areas for future research.
- Summarize the main findings of the Construction Of A Battery Changer Using Silicon Controlled Regulator SCR study and restate its significance.
- List all the sources you cited in Construction Of A Battery Changer Using Silicon Controlled Regulator SCR project, following a specific citation style (e.g., APA, MLA, Chicago).